PCB Test Facilities
| No. | Machine | Maker | Model |
| Appearance | Specification | ||
| 1 | Drilling Machine | Hitachi Via Mechanics | ND-1V212 |
 |
2 machines in facility, Independent
3 spindles control machine with one 200krpm spindle and 2 160krpm spindles for 3.175mm drill shank |
||
| 2 | Drilling Machine | Hitachi Via Mechanics | ND-1W212 |
 |
Independent 2 spindles control machine with 125krpm spindles for 3.175mm drill shank |
||
| 3 | Drilling Machine | Hitachi Via Mechanics | ND-1V211 |
 |
1spindle machine with 160krpm spindle for 2 mm drill shank | ||
| 4 | Routing Machine | Hitachi Via Mechanics | NR-2G210 |
 |
2
axis machine Spindle speed:15-80krpm Table feed: 50m/min(Max) Retract rate: 25.4m/min(Max) Z axis feed rate: 0.1-10m/min |
||
| 5 | Drilling
Machine Routing Machine |
Schmoll Machinen | System 1-1 Linear DK |
 |
2 spindle machine with 180krpm/125krpm spindle for 3.175 mm drill shank |
||
| 6 | Drilling Machine | Schmoll Machinen | MX1-300DH |
 |
2 spindle machine with 300krpm and 200krpm spindles for 3.175mm drill shank |
||
| 7 | PWB Hole Tester | Hitachi Via Mechanics | HT-1AM |
 |
Measuring
area:650x550mm Measuring thickness:0.1-5.0mm Measuring accuracy:±0.005mm Measuring time:Less than 8min (PWB 500x500mm) |
||
| 8 | Surface Analyzer | TAYLOR HOBSON | Form Talysarf 2 |
 |
Traverse length:120mm Measuring speed:1.0 and 0.5mm/sec Pickup resolution: 426nm Pickup radius accuracy: <0.5% Pickup linearity: <0.1% |
||
| 9 | SEM | ABT | SX-40A |
 |
Magnification: x10
- x150,000 Maximum specimen size: ø100xt1.0mm |
||
| 10 | FE SEM | Hitachi | S-4100 |
 |
Magnification: x20 -
x300,000 Maximum specimen size: ø100xt1.0mm |
||
| 11 | Laser microscope | KEYENCE | VK-8500 |
 |
Magnification:
x200, x400, x1000, x2000 resolution of Z axis: 0.01mm Work area: 70 x 70 mm Z axis stroke: 28mm |
||
| 12 | Digital Micro Scope | KEYENCE | VH-6300 |
 |
Magnification: x150
to x800 Color TFT display installed. 0.9million pixels CCD image sensor. 1.44M floppy disk drive installed |
||
| 13 | T.I.R checker | UNION TOOL | OPTECH-RI-III |
 |
Gauge pin:
ø3.175mm Range: 0.250mm Min. count: 0.001mm Max. revolution: 200krpm |
||
| 14 | T.I.R checker | UNION TOOL | OPTECH-RI-IV |
 |
Gauge pin:
ø2.0mm Range: 0.250mm Min. count: 0.001mm Max. revolution: 300krpm |
||
| 15 | Spindle Condition Checker | UNION TOOL | PV-CHECKER |
 |
Bush Flatness Contact
:Check by PV film Maximum Pressure: 250N Maximum Vacuum: 300hPa Dimention: W110 x D90 x H21 Weight Indicator: 0.7kgSensor 0.4kg |
||
| 16 | Micro hardness tester | AKASHI | MVK-H2 |
 |
Test Load: 9.807 -
19610mN Loading Speed: 1,3,10,30,60mm/s |
||
| 17 | Rockwell hardness tester | AKASHI | ARK-500 |
 |
Loading Speed: 150,100,60kgf | ||
| 18 | Dynamometer | KISLER | 9272 |
 |
Work area: ±50mm Load renge: -6 - 24kN Max bending moment: ±400Nm with Multichannel charge amplifier |
||
| 19 | Diameter checker | UNION TOOL | OPTECH-LS |
 |
Laser type non-contact measuring device | ||
| 20 | Diameter checker | UNION TOOL | BMM-1 |
 |
Laser type non-contact measuring device | ||
| 21 | X-Ray apparatus | JAPAN HITEX | HK-80R |
 |
Board size : Less than
600x650mm, t 10mm Magnification : x20 |
||
| 22 | Grinding Machine for Cross Section | Buehler | METASERV 2000 |
 |
– | ||
| 23 | Tool Microscope | OLYMPUS | STM |
| – | Magnification: 10x10= x100 totally |
